Demonstration of 10 nm Ferroelectric Al0.7Sc0.3N-Based Capacitors for Enabling Selector-Free Memory Array.

In this work, 10 nm scandium-doped aluminum nitride (AlScN) capacitors are demonstrated for the construction of the selector-free memory array application. The 10 nm Al0.7Sc0.3N film deposited on an 8-inch silicon wafer with sputtering technology exhibits a large remnant polarization exceeding 100 µC/cm2 and a tight distribution of the coercive field, which is characterized by the positive-up-negative-down (PUND) method. As a result, the devices with lateral dimension of only 1.5 µm show a large memory window of over 250% and a low power consumption of ~40 pJ while maintaining a low disturbance rate of <2%. Additionally, the devices demonstrate stable multistate memory characteristics with a dedicated operation scheme. The back-end-of-line (BEOL)-compatible fabrication process, along with all these device performances, shows the potential of AlScN-based capacitors for the implementation of the high-density selector-free memory array.

Leakage Mechanism and Cycling Behavior of Ferroelectric Al0.7Sc0.3N.

Ferroelectric scandium-doped aluminum nitride (Al1-xScxN) is of considerable research interest because of its superior ferroelectricity. Studies indicate that Al1-xScxN may suffer from a high leakage current, which can hinder further thickness scaling and long-term reliability. In this work, we systematically investigate the origin of the leakage current in Al0.7Sc0.3N films via experiments and theoretical calculations. The results reveal that the leakage may originate from the nitrogen vacancies with positively charged states and fits well with the trap-assisted Poole-Frenkel (P-F) emission. Moreover, we examine the cycling behavior of ferroelectric Al0.7Sc0.3N-based FeRAM devices. We observe that the leakage current substantially increases when the device undergoes bipolar cycling with a pulse amplitude larger than the coercive electric field. Our analysis shows that the increased leakage current in bipolar cycling is caused by the monotonously reduced trap energy level by monitoring the direct current (DC) leakage under different temperatures and the P-F emission fitting.

Hierarchical porous mussel shells as soil amendment for oil spill remediation.

In this work, a new type of micromesoporous substance was prepared with fatty alcohol-polyoxyethylene ether (AEO) surfactant freezing penetration and pyrolysis using shells as raw materials. The obtained material exhibited good adsorbability and could be added to oil-contaminated soil to adsorb the pollutant, which resulted in the regeneration of the initially polluted soil. It was determined that the main component of the developed substance was CaCO3. Importantly, the conducted experiments revealed that the obtained mussel micromesoporous material displayed certain adsorption effects toward petroleum hydrocarbons in a diesel solution. Moreover, it was found that chemical adsorption was more optimal than physical adsorption. The soil remediation effect was the best when the content of the mussel micromesoporous material in the soil was 400 g/kg. Under these conditions, the removal rate of petroleum hydrocarbon was established at 49.38%. This study indicated that micromesoporous material has great potential in the application of oil contaminated soil remediation.

An abundant porous biochar material derived from wakame (Undaria pinnatifida) with high adsorption performance for three organic dyes.

In this study, an activated wakame biochar material (AWBM) was prepared by a one-step calcination and activation method, whose adsorption performances for methylene blue (MB), Rhodamine B (RB) and malachite green (MG) were also analyzed. The results showed AWBM was a mesoporous fluffy structure material with a higher specific surface (1156.25 m2/g), exhibiting superior adsorption capacities for MB (841.64 mg/g), RB (533.77 mg/g) and MG (4066.96 mg/g), respectively. In addition, FT-IR analysis showed that AWBM possessed abundant active groups (such as -OH, -CO and -CH), further enhancing the adsorption efficiencies. The Langmuir model could better fit the three dyes adsorption isotherms process using AWBM, and the Pseudo-second-order model could better describe the adsorption kinetic experimental data. The thermodynamic analysis showed that the three dyes adsorption using AWBM was spontaneous endothermic reaction. This study suggests AWBM has enormous potential in the application of removing organic dyes from wastewater.

Magnetic activated biochar nanocomposites derived from wakame and its application in methylene blue adsorption.

In this work, magnetic wakame biochar nanocomposites for the first time had been synthesized to investigate their adsorption to methylene blue dye. As-prepared magnetic biochar samples were obtained by the impregnation method to load nickel on wakame biochar via one-step carbonization with activation agent KOH at 800 °C. The prepared samples were characterized by BET, XRD, FTIR, Raman, SEM, TEM and so on. The results exhibited that the maximum adsorption capacity of BW(Ni)0.5 to methylene blue could reach 479.49 mg/g at 20 °C. The adsorption behavior was more suitable for Langmuir isotherm equation and the kinetic data were most consistent with the pseudo second-order model. And also, the adsorption reaction was a spontaneous and endothermic process. After five cycles, it was found that BW(Ni)0.5 had a high adsorption capacity for methylene blue (117.58 mg/g). This study demonstrated that wakame biochar could have great potential in dye wastewater treatment.

Facile Preparation of Charcoal Nanomaterial from Fishery Waste with Remarkable Adsorption Ability.

In this study, modified activated fishbone charcoal (MAFC) was successfully prepared to remove emulsified oil from oily wastewater. Various characteristic techniques, including SEM, XRD, FTIR, and BET, were employed to investigate the morphology, texture, and surface properties of as-prepared samples. BET results demonstrated that the specific surface area of fishbone charcoal increased from 69.8 m2/g to 206.0 m2/g after treatment with K2CO3 as an activating agent, while the total pore volume of MAFC increased from 0.003 cm3/g to 0.3 cm3/g, accompanied by the formation of abundant pore structures. It was observed that 90.1% of emulsified oil (100 mg/L) was successfully removed by MAFC under our experimental conditions. The results of a kinetic and isotherm model analysis indicated that the adsorption experimental data were not only consistent with the Langmuir adsorption isotherm but were also well-described by the pseudo-second-order adsorption model. It is expected that this highly efficient and inexpensive MAFC can be a promising bio-adsorbent for removing organic pollutants from industrial wastewater.

Modified mussel shell powder for microalgae immobilization to remove N and P from eutrophic wastewater.

In this work, calcined mussel shell powder (CMSP) was activated by K2CO3 (K-CMSP), and this porous K-CMSP surface was modified by L-arginine (L-ARG) to render porous biomass a positively charged surface, which was innovatively utilized as a carrier to immobilize microalgae by adsorption via electrostatic interactions. The pore and the surface structures of CMSP and K-CMSP were characterized by XRD, FTIR, BET and SEM. The surface morphology of immobilized microalgae was visualized via using inverted optical microscope and SEM. It was found that microalgae could survive for 60 days, and the loss rate of chlorophyll-a preserved at -24 °C was the lowest, 44.73%. The microalgae could revive to normal growth level within 10 days and the cell content of microalgae was the highest at 25 °C, 2.8022 × 106 cell/mL. At 25 °C, the highest removal rate of N and P was obtained about 95.0% and 88.63%, respectively.

Effective Adsorption of Diesel Oil by Crab-Shell-Derived Biochar Nanomaterials.

This study, for the first time, rendered crab shell activated biochar modified by potassium hydroxide (KOH) impregnation (CSAB), revealing a new potential application in the removal of diesel oil from oily wastewater. The structural characteristics of crab shell biochar (CSB) and CSAB were investigated by SEM, and the crystal structure and optical properties of as-prepared samples were analyzed using XRD and FTIR. Results showed that CSAB had stratified surface structure morphology, abundant functional groups, and that its high specific surface area could reach up to 2441 m²/g, which was about eight times larger than that of untreated CSB (307 m²/g). An adsorption isotherm study indicated that the actual adsorption process both of CSAB and CSB were found to fit better with the Freundlich equation. Moreover, chemical interaction controlled the adsorption kinetics efficiency while the adsorption equilibrium capacity was 93.9 mg/g. Due to its highly developed pore structure, unique surface characteristics, and effective adsorption performance, this low-cost activated carbon had the potential to serve as an efficient adsorbent for water pollution purification.

Preparation and Characterization of Nanoporous Activated Carbon Derived from Prawn Shell and Its Application for Removal of Heavy Metal Ions.

The aim of this study was to optimize the adsorption performance of activated carbon (AC), derived from the shell of Penaeus vannamei prawns, on heavy metal ions. Inexpensive, non-toxic, and renewable prawn shells were subjected to carbonization and, subsequently, KOH-activation to produce nanoporous K-Ac. Carbonized prawn shells (CPS) and nanoporous KOH-activated carbon (K-Ac) from prawn shells were prepared and characterized by FTIR, XRD, BET, SEM, and TEM. The results showed that as-produced K-Ac samples were a porous material with microporous and mesoporous structures and had a high specific surface area of 3160 m²/g, average pore size of about 10 nm, and large pore volume of 2.38 m³/g. Furthermore, batches of K-Ac samples were employed for testing the adsorption behavior of Cd2+ in solution. The effects of pH value, initial concentration, and adsorption time on Cd2+ were systematically investigated. Kinetics and isotherm model analysis of the adsorption of Cd2+ on K-Ac showed that experimental data were not only consistent with the Langmuir adsorption isotherm, but also well-described by the quasi-first-order model. Finally, the adsorption behaviors of as-prepared K-Ac were also tested in a ternary mixture of heavy metal ions Cu2+, Cr6+, and Cd2+, and the total adsorption amount of 560 mg/g was obtained.

Preparation and evaluation of a hierarchical Bi2MoO6/MSB composite for visible-light-driven photocatalytic performance.

In this study, waste mussel shells were used to remove dyes in aqueous solution. Mussel shell was prepared into mussel shell biochar (MSB), which was used as a carrier to support Bi2MoO6. A novel Bi2MoO6/MSB composite photocatalyst was developed by the hydrothermal synthesis method. The as-synthesized sample was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), N2 adsorption-desorption method, Fourier transform infrared spectroscopy (FTIR) and UV-vis diffuse reflectance spectra (DRS). Then, the photocatalytic activity of the prepared samples was determined by testing the photodegradation of Rhodamine B (RhB) under visible-light (λ > 420 nm) irradiation. The pre exfoliated layered MSB was an excellent supporting matrix for the growth of Bi2MoO6 nanoflakes. The obtained hierarchical Bi2MoO6/MSB composites exhibited significantly enhanced performance for photocatalytic degradation of RhB compared with pure Bi2MoO6 under visible light irradiation because of the improved electron-hole pair separation, which boosted the number of exposed catalytic active sites. Moreover, the Bi2MoO6/MSB composite photocatalyst is of good stability and reusability.

High-Magnetization Tetragonal Ferrite-Based Films Induced by Carbon and Oxygen Vacancy Pairs.

Herein, a low-temperature thermal decomposition method is utilized to grow new stable tetragonal Fe3O4-based thick ferrite films. The tetragonal Fe3O4-based film possesses high saturation magnetization of ∼800 emu/cm3. Doping with approximately 10% Co results in a high-energy product of ∼10.9 MGOe with perpendicular magnetocrystalline anisotropy, whereas doping with Ni increases electrical resistivity by a factor of 6 and retains excellent soft magnetic properties (high saturation magnetization and low coercivity). A combined experimental and first-principles study reveals that carbon interstitials (CiB) and oxygen vacancies (VO) form CiB-VO pairs which stabilize the tetragonal phase and enhance saturation magnetization. The magnetization enhancement is further attributed to local ferromagnetic coupling between FeA and FeB induced by CiB-VO pairs in a tetragonal spinel ferrite lattice.

Preparation and Characterization of Macroalgae Biochar Nanomaterials with Highly Efficient Adsorption and Photodegradation Ability.

In this study, carbonized kelp biochar (AKB) modified by KOH impregnation and photocatalytic Bi2MoO6/AKB composite (BKBC) nanomaterials were the first time successfully synthesized for efficient removal of dyes in aqueous solution. BET, XRD, FT-IR, and SEM were employed to characterize as-prepared samples. UV-vis and other test results indicated that the removal efficiency of methylene blue (MB) was 61.39% and 94.12% for BKBC and AKB, respectively, which was up to 13 times and 20 times higher in comparison with pure Bi2MoO6 (PBM). In addition, the equilibrium adsorption capacity of MB could reach up to 324.1 mg/g for AKB. This high dyes adsorption performance could be likely attributed to its high specific surface area (507.177 m²/g) and its abundant presence of various functional groups such as ⁻OH and =C⁻H on AKB. Particularly, the existing of amorphous carbon and transition metal oxides, such as Fe2O3 and Mn5O8, could be beneficial for the photodegradation of MB for AKB. Meanwhile, experimental data indicated that adsorption kinetics complied with the pseudo-second order model well, and all of the tests had satisfactory results in terms of the highly efficient adsorption and photodegradation activity of AKB nanomaterials, which suggested its great potential in wastewater treatment.

Calcined Mussel Shell Powder (CMSP) via Modification with Surfactants: Application for Antistatic Oil-Removal.

Biomass is known to efficiently adsorb pollutants from wastewater. In this paper, we demonstrated that a new antistatic oil-cleaning material can be prepared and assembled by using two surfactants, alkyl polyglucosides (APG) and dimethyl octadecyl hydroxy ethyl ammonium nitrate (SN), to modify calcined mussel shell powder (CMSP) through a two-step hydrotherm-assisted adsorption. The pore size and structure of CMSP was measured by BET and a contact angle meter was used to characterize the surface wetting ability. XRD, FTIR, XPS, SEM, TEM, and HRTEM were employed to determine the surface structure of CMSP modified by surfactants APG and SN (MMO). In order to further characterize properties of the surface morphology and crystal structure, the HRTEM was employed to show that the MMO surface had a single crystal structure: calcite, with a crystal plane spacing of 0.2467 nm. The surface of MMO appeared to be fluffy and disperse. The antistatic and degreasing ability of as-prepared samples (MMO) was evaluated by a ZC-36 high resistance meter and BD-457 whiteness meter. The results showed that when the calcination temperature of CMSP reached 1000 °C, and the addition amount of APG and SN was 0.8 g and 0.16 g, it had an optimum antistatic effect with a surface resistivity (Rs) of 1.35 × 108 Ω, and a detergency rate to oil of 17.35%. This study aims to embrace a green solution to reduce environmental pressure and make use of waste, which is of great significance to environmental protection.

Facile Preparation of Nano-Bi2MoO6/Diatomite Composite for Enhancing Photocatalytic Performance under Visible Light Irradiation.

In this work, a new nano-Bi2MoO6/diatomite composite photocatalyst was successfully synthesized by a facile solvothermal method. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and UV-vis diffuse reflection spectroscopy (DRS) were employed to investigate the morphology, crystal structure, and optical properties. It was shown that nanometer-scaled Bi2MoO6 crystals were well-deposited on the surface of Bi2MoO6/diatomite. The photocatalytic activity of the obtained samples was evaluated by the degradation of rhodamine B (RhB) under the visible light (λ > 420 nm) irradiation. Moreover, trapping experiments were performed to investigate the possible photocatalytic reaction mechanism. The results showed that the nano-Bi2MoO6/diatomite composite with the mass ratio of Bi2MoO6 to diatomaceous earth of 70% exhibited the highest activity, and the RhB degradation efficiency reached 97.6% within 60 min. The main active species were revealed to be h⁺ and•O2-. As a photocatalytic reactor, its recycling performance showed a good stability and reusability. This new composite photocatalyst material holds great promise in the engineering field for the environmental remediation.

Novel room-temperature spin-valve-like magnetoresistance in magnetically coupled nano-column Fe3O4/Ni heterostructure.

Herein, we design a room-temperature spin-valve-like magnetoresistance in a nano-column Fe3O4/Ni heterostructure without using a non-magnetic spacer or pinning layer. An Fe3O4 nano-column film is self-assembled on a Ni underlayer by the thermal decomposition method. The wet-chemical self-assembly is facile, economical and scalable. The magnetoresistance (MR) response of the Ni underlayer in the heterostructure under positive and negative out-of-plane magnetic fields differ by ∼0.25 at room temperature and ∼0.43 at 100 K. We attribute the spin-valve-like magnetoresistance to the unidirectional magnetic anisotropy of the Ni underlayer when being magnetically coupled by the Fe3O4 nano-column film. The out-of-plane negative-field magnetization is higher than the positive-field magnetization, affirming the unidirectional magnetic anisotropy of the Fe3O4/Ni heterostructure. Temperature-dependent magnetic and resistivity studies illustrate a close correlation between the magnetization transition of Fe3O4 and resistivity transition of Ni and prove a magnetic coupling between the Fe3O4 and Ni. First-principles calculations reveal that the Fe3O4/Ni model under a negative magnetic field is energetically more stable than that under a positive magnetic field. Furthermore, partial density of states (PDOS) analysis demonstrates the unidirectional magnetic anisotropy of the Ni 3d orbital. This is induced by the strong ferromagnetic coupling between Fe3O4 and Ni via oxygen-mediated Fe 3d-O 2p-Ni 3d hybridizations.

A new hand-held microfluidic cytometer for evaluating irradiation damage by analysis of the damaged cells distribution.

Space radiation brings uneven damages to cells. The detection of the distribution of cell damage plays a very important role in radiation medicine and the related research. In this paper, a new hand-held microfluidic flow cytometer was developed to evaluate the degree of radiation damage of cells. The device we propose overcomes the shortcomings (e.g., large volume and high cost) of commercial flow cytometers and can evaluate the radiation damage of cells accurately and quickly with potential for onsite applications. The distribution of radiation-damaged cells is analyzed by a simultaneous detection of immunofluorescence intensity of γ-H2AX and resistance pulse sensor (RPS) signal. The γ-H2AX fluorescence intensity provides information of the degree of radiation damage in cells. The ratio of the number of cells with γ-H2AX fluorescence signals to the total numbers of cells detected by RPS indicates the percentage of the cells that are damaged by radiation. The comparison experiment between the developed hand-held microfluidic flow cytometer and a commercial confocal microscope indicates a consistent and comparable detection performance.

Fucoidan from sea cucumber may improve hepatic inflammatory response and insulin resistance in mice.

Nutrition excess-induced inflammation positively contributed to insulin resistance. Fucoidan from sea cucumber can increase glucose translocation in skeletal muscle. However, its effects on inflammation-associated insulin resistance are not understood. We investigated fucoidan from Isostichopus badionotus (Ib-FUC)-alleviated inflammatory response and signaling as well as -improved insulin resistance in the liver of obesity mice. The results showed that Ib-FUC reduced body weight and glucose levels, increased insulin sensitivity, and inhibited serum lipid concentrations. Meanwhile, Hepatic glycogen synthesis was promoted by Ib-FUC via activation of the PI3K/PKB/GSK-3ß signaling and regulation of glucose metabolism-related enzymatic activities. Ib-FUC regulated serum inflammatory cytokines and their mRNA expression in the liver. Ib-FUC-induced inactivation of the JNK and IKKß/NFκB pathways was involved in the activation of insulin signal cascade and inflammatory factor production. These findings suggested that Ib-FUC supplementary-induced alleviation of inflammatory response could be a mechanism responsible for its beneficial effects against hepatic insulin resistance.

Strain Engineering of Octahedral Rotations and Physical Properties of SrRuO3 Films.

Strain engineering is an effective way to modify functional properties of thin films. Recently, the importance of octahedral rotations in pervoskite films has been recognized in discovering and designing new functional phases. Octahedral behavior of SrRuO3 film as a popular electrode in heterostructured devices is of particular interest for its probable interfacial coupling of octahedra with the functional overlayers. Here we report the strain engineering of octahedral rotations and physical properties that has been achieved in SrRuO3 films in response to the substrate-induced misfit strains of almost the same amplitude but of opposite signs. It shows that the compressively strained film on NdGaO3 substrate displays a rotation pattern of a tetragonal phase whilst the tensilely strained film on KTaO3 substrate has the rotation pattern of the bulk orthorhombic SrRuO3 phase. In addition, the compressively strained film displays a perpendicular magnetic anisotropy while the tensilely strained film has the magnetic easy axis lying in the film plane. The results show the prospect of strain engineered octahedral architecture in producing desired property and novel functionality in the class of perovskite material.

Fucosylated chondroitin sulphate from Cusumaria frondosa mitigates hepatic endoplasmic reticulum stress and inflammation in insulin resistant mice.

Endoplasmic reticulum (ER) stress-associated inflammation positively contributes to insulin resistance. It is also known that fucosylated chondroitin sulphate from Cusumaria frondosa (Cf-CHS) can mitigate insulin resistance; however, its effects on ER stress and inflammation are not well understood. Therefore, we investigated whether Cf-CHS-influenced ER stress, inflammatory response and signaling in insulin-resistant mice. Our results showed that Cf-CHS lowered serum and hepatic ROS, NO, and FFA levels. Furthermore, Cf-CHS decreased serum proinflammatory cytokines TNF-α, CRP, MIP-1, IL-1ß and IL-6 concentrations as well as their hepatic mRNA expression, and increased the anti-inflammatory cytokine IL-10 levels. Moreover, Cf-CHS reduced the ER stress markers Bip, ATF6, PERK, and XBP1 mRNA or protein expression, and PERK, eIF2α, and IRE1α phosphorylation. These reductions were accompanied by a reduced activation of JNK1 and IKKß, NFκB nuclear translocation, and IR/IRS-2 serine phosphorylation in Cf-CHS-treated mice. These findings suggested that the Cf-CHS supplementary-induced alleviation of RE stress-associated inflammation could be the mechanism responsible for its beneficial effects against insulin resistance.

Guest-cage atomic interactions in a clathrate-based phase-change material.

New clathrate-based phase-change materials with cage-like structures incorporating Cs and Ba guest atoms, are reported as a means of altering crystallization and amorphization behavior by controlling 'guest-cage' interactions via intra-complex guest vibrational effects. Both a high resistance to spontaneous crystallization, and long retention of the amorphous phase are achieved, as well as a low melting energy. This approach provides a route for achieving cage-controlled semiconductor devices.